How To Torque Cylinder Head Bolts - EricTheCarGuy

How To Torque Cylinder Head Bolts - EricTheCarGuy http://www.ericthecarguy.com/ Well this was a fun one to make. I believe I covered everything but if you feel I haven't please let me know in the comments below as well as any tips you might have to add as well. I'm not trying to make a big deal about "pound feet" or "foot pounds" I'm just trying to put that out there, the important thing is that you get the proper torque and get the job done right in my opinion, what you decide to call it is up to you. --- Click below and Stay Dirty Visit me at EricTheCarGuy.com http://ericthecarguy.com/ Visit EricTheCarGuy Forum http://www.ericthecarguy.com/forum/default.aspx Visit my Facebook Page: http://www.facebook.com/EricTheCarGuy --- ETCG Due to factors beyond the control of EricTheCarGuy, it cannot guarantee against unauthorized modifications of this information, or improper use of this information.  EricTheCarGuy assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. EricTheCarGuy recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video.  Due to factors beyond the control of EricTheCarGuy, no information contained in this video shall create any express or implied warranty or guarantee of any particular result.  Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not EricTheCarGuy.

TARGET AD 2
2010/08/30 EricTheCarGuy   Share on Facebook

RELATED VIDEOS

HOW TO RESURFACE A WARPED CYLINDER HEAD AT HOME WITH SAND PAPER
Play Video

HOW TO RESURFACE A WARPED CYLINDER HEAD AT HOME WITH SAND PAPER

2014/08/20
How to Torque and Angle Cylinder Head
Play Video

How to Torque and Angle Cylinder Head

2017/05/06
Cylinder Head 105 - Valve Job Basics
Play Video

Cylinder Head 105 - Valve Job Basics

2012/06/15
8 Ways Police STOP Dangerous Cars
Play Video

8 Ways Police STOP Dangerous Cars

2017/11/02
Replace a Cylinder Head Gasket Yourself and do it RIGHT! Part 1
Play Video

Replace a Cylinder Head Gasket Yourself and do it RIGHT! Part 1

2014/04/05
How To Remove and Replace Valves in a Cylinder Head -EricTheCarGuy
Play Video

How To Remove and Replace Valves in a Cylinder Head -EricTheCarGuy

2014/03/22
How To Perform a Compression Test - EricTheCarGuy
Play Video

How To Perform a Compression Test - EricTheCarGuy

2010/01/17
Top 15 Unusual Strangest Engines Starting Up And Running [VIDEOS]
Play Video

Top 15 Unusual Strangest Engines Starting Up And Running [VIDEOS]

2017/10/04
What Happens When You Don
Play Video

What Happens When You Don't Change Your Oil Part 1

2010/02/10
BANNED Race Cars | Too overpowered, dangerous and "too costly" | TOP 5 PART 2
Play Video

BANNED Race Cars | Too overpowered, dangerous and "too costly" | TOP 5 PART 2

2017/03/27
► Bentley Factory - W12 Engine
Play Video

► Bentley Factory - W12 Engine

2013/09/25
Torque & Angle Explained with a Stress / Strian diagram
Play Video

Torque & Angle Explained with a Stress / Strian diagram

2011/10/17
Removing Broken Fasteners -EricTheCarGuy
Play Video

Removing Broken Fasteners -EricTheCarGuy

2014/01/27
Torquing on a Cylinder Head
Play Video

Torquing on a Cylinder Head

2010/06/06
How to use a torque wrench
Play Video

How to use a torque wrench

2009/07/13
How to Change Tie Rods (inner and outer tie rod ends)
Play Video

How to Change Tie Rods (inner and outer tie rod ends)

2013/12/05
Engine Building Part 7:   Installing Heads, Head Gaskets, Head Bolts, Rockers, & Setting Lash
Play Video

Engine Building Part 7: Installing Heads, Head Gaskets, Head Bolts, Rockers, & Setting Lash

2014/01/19
Seafoam--can
Play Video

Seafoam--can't believe what it did to my engine!!

2017/03/11
Does Stop Leak Work? - EricTheCarGuy
Play Video

Does Stop Leak Work? - EricTheCarGuy

2010/12/13
Basic valve job
Play Video

Basic valve job

2009/12/08
How to Break In A New or Rebuilt Engine - EricTheCarGuy
Play Video

How to Break In A New or Rebuilt Engine - EricTheCarGuy

2012/03/08
How to use an angle degree torque gauge - Auto Information Series
Play Video

How to use an angle degree torque gauge - Auto Information Series

2013/11/16
Engine Building Part 1:  Blocks
Play Video

Engine Building Part 1: Blocks

2013/08/25
Top 5  Mods for Maximum HP and Torque
Play Video

Top 5 Mods for Maximum HP and Torque

2017/09/26
Powered by YouTube

Disclaimer

None of the audio/visual content is hosted on this site. All media is embedded from other sites such as GoogleVideo, YouTube etc. Therefore, this site has no control over the copyright issues of the streaming media.

All issues concerning copyright violations should be aimed at the sites hosting the material. This site does not host any of the streaming media and the owner has not uploaded any of the material to the video hosting servers. Anyone can find the same content on Google Video or YouTube by themselves.

The owner of this site cannot know which documentaries are in public domain, which has been uploaded to e.g. YouTube by the owner and which has been uploaded without permission. The copyright owner must contact the source if he wants his material off the Internet completely.